[ aws ]
This section explains prominent concepts and notations in the set of high-level S3 commands provided.
Whenever using a command, at least one path argument must be specified. There
are two types of path arguments:
LocalPath: represents the path of a local file or directory. It can be
written as an absolute path or relative path.
S3Uri: represents the location of a S3 object, prefix, or bucket. This
must be written in the form
the specified S3 bucket,
mykey is the specified S3 key. The path argument
must begin with
s3:// in order to denote that the path argument refers to
a S3 object. Note that prefixes are separated by forward slashes. For
example, if the S3 object
myobject had the prefix
S3 key would be
myprefix/myobject, and if the object was in the bucket
S3Uri would be
S3Uri also supports S3 access points. To specify an access point, this
value must be of the form
s3://<access-point-arn>/<key>. For for example if
the access point
myaccesspoint to be used has the ARN:
arn:aws:s3:us-west-2:123456789012:accesspoint/myaccesspoint and the object
being accessed has the key
mykey, then the
S3URI used must be:
Similar to bucket names, you can also use prefixes with access point ARNs for
S3Uri. For example:
The higher level
s3 commands do not support access point object ARNs.
For example, if the following was specified:
S3URI will resolve to the object key
Every command takes one or two positional path arguments. The first path argument represents the source, which is the local file/directory or S3 object/prefix/bucket that is being referenced. If there is a second path argument, it represents the destination, which is the local file/directory or S3 object/prefix/bucket that is being operated on. Commands with only one path argument do not have a destination because the operation is being performed only on the source.
Some commands perform operations only on single files and S3 objects. The
following commands are single file/object operations if no
flag is provided.
For this type of operation, the first path argument, the source, must exist and be a local file or S3 object. The second path argument, the destination, can be the name of a local file, local directory, S3 object, S3 prefix, or S3 bucket.
The destination is indicated as a local directory, S3 prefix, or S3 bucket
if it ends with a forward slash or back slash. The use of slash depends
on the path argument type. If the path argument is a
the type of slash is the separator used by the operating system. If the
path is a
S3Uri, the forward slash must always be used. If a slash
is at the end of the destination, the destination file or object will
adopt the name of the source file or object. Otherwise, if there is no
slash at the end, the file or object will be saved under the name provided.
See examples in
mv to illustrate this description.
Some commands only perform operations on the contents of a local directory or S3 prefix/bucket. Adding or omitting a forward slash or back slash to the end of any path argument, depending on its type, does not affect the results of the operation. The following commands will always result in a directory or S3 prefix/bucket operation:
Currently, there is no support for the use of UNIX style wildcards in
a command’s path arguments. However, most commands have
--include "<value>" parameters that can achieve the desired result.
These parameters perform pattern matching to either exclude or include
a particular file or object. The following pattern symbols are supported.
*: Matches everything
?: Matches any single character
[sequence]: Matches any character in
[!sequence]: Matches any character not in
Any number of these parameters can be passed to a command. You can do this by
--include argument multiple times, e.g.
--include "*.txt" --include "*.png".
When there are multiple filters, the rule is the filters that appear later in
the command take precedence over filters that appear earlier in the command.
For example, if the filter parameters passed to the command were
--exclude "*" --include "*.txt"
All files will be excluded from the command except for files ending with
.txt However, if the order of the filter parameters was changed to
--include "*.txt" --exclude "*"
All files will be excluded from the command.
Each filter is evaluated against the source directory. If the source location is a file instead of a directory, the directory containing the file is used as the source directory. For example, suppose you had the following directory structure:
/tmp/foo/ .git/ |---config |---description foo.txt bar.txt baz.jpg
In the command
aws s3 sync /tmp/foo s3://bucket/ the source directory is
/tmp/foo. Any include/exclude filters will be evaluated with the source
directory prepended. Below are several examples to demonstrate this.
Given the directory structure above and the command
aws s3 cp /tmp/foo s3://bucket/ --recursive --exclude ".git/*", the
.git/description will be excluded from the
files to upload because the exclude filter
.git/* will have the source
prepended to the filter. This means that:
/tmp/foo/.git/* -> /tmp/foo/.git/config (matches, should exclude) /tmp/foo/.git/* -> /tmp/foo/.git/description (matches, should exclude) /tmp/foo/.git/* -> /tmp/foo/foo.txt (does not match, should include) /tmp/foo/.git/* -> /tmp/foo/bar.txt (does not match, should include) /tmp/foo/.git/* -> /tmp/foo/baz.jpg (does not match, should include)
aws s3 cp /tmp/foo/ s3://bucket/ --recursive --exclude "ba*"
/tmp/foo/ba* -> /tmp/foo/.git/config (does not match, should include) /tmp/foo/ba* -> /tmp/foo/.git/description (does not match, should include) /tmp/foo/ba* -> /tmp/foo/foo.txt (does not match, should include) /tmp/foo/ba* -> /tmp/foo/bar.txt (matches, should exclude) /tmp/foo/ba* -> /tmp/foo/baz.jpg (matches, should exclude)
Note that, by default, all files are included. This means that
providing only an
--include filter will not change what
files are transferred.
--include will only re-include files that
have been excluded from an
--exclude filter. If you only want
to upload files with a particular extension, you need to first exclude
all files, then re-include the files with the particular extension.
This command will upload only files ending with
aws s3 cp /tmp/foo/ s3://bucket/ --recursive --exclude "*" --include "*.jpg"
If you wanted to include both
.jpg files as well as
.txt files you
aws s3 cp /tmp/foo/ s3://bucket/ --recursive \ --exclude "*" --include "*.jpg" --include "*.txt"
See ‘aws help’ for descriptions of global parameters.
aws s3 <Command> [<Arg> ...]
See ‘aws help’ for descriptions of global parameters.